• Moderators, please send me a PM if you are unable to access mod permissions. Thanks, Habsy.

Hey Nerds: Vynil Edition

Artnes

Well-known member
Got my hands on a vintage rig in great shape but its spinning at just over 34 rpms.

Sony HP 219 built in 75 so finding manuals are not easy. Any suggestions on easy ways to adjust to slow it down

20211023_213123_remastered.jpg


Screenshot_20211023-213141.jpg
 
Last edited:
Could be an issue with your speed switch (or pitch control if it has one).

could be dirt/gunk (on those switches or elsewhere)

tough to isolate without a manual or opening the thing up.

so you know if it’s direct or belt drive? If the latter, it could be a belt issue.
 
Could be an issue with your speed switch (or pitch control if it has one).

could be dirt/gunk (on those switches or elsewhere)

tough to isolate without a manual or opening the thing up.

so you know if it’s direct or belt drive? If the latter, it could be a belt issue.

Im going to open it up today and clean it up and see if the belt is frayed or stretched.

I read you can boil the belt for 10 mins to get it to shrink back to normal. Ill try that first but if that doesnt work Ill just order a new one..Probably not a bad idea to have an extra one on hand anyway
 
If you can pull the knobs/face off of the unit, you should spray some contact cleaner into the knob/switch contacts. Not sure if it will help your speed issue, but would def help with volume/tone issues and keep everything sounding clean.
 
Looking at the pic — seems like a pretty simple set up so will likely be dirt or a belt issue.

I’d try cleaning before messing around with belt, unless when you open it up it’s clear that the belt is the issue.
 
Also (I’m not a expert here) but I think belt issues usually cause slow downs rather than causing the table to speed up.
 
Pulled off the platter and gave it a good cleaning and its running at 33.33 so that did the trick.

My parents were going to throw their collection out (75 LPs) and I couldn't let that happen so I ended up buying an extra suitcase to fly them home during my trip this summer. Imagine these ending up in a landfill

20211024_102622.jpg


20211024_105006.jpg
 
Last edited:
Im going to open it up today and clean it up and see if the belt is frayed or stretched.

I read you can boil the belt for 10 mins to get it to shrink back to normal. Ill try that first but if that doesnt work Ill just order a new one..Probably not a bad idea to have an extra one on hand anyway
This will probably work. If not. Tape.
 
Whats an acceptable percentage to be within of RPM?

Nailed it at 33.33 when I first cleaned it but after a few rotations Im hovering around 33.82 so 1.45%. I can notice the speed increase in some songs. Enough to annoy me though I know with these old machines its hard to get it perfect
 
if it stays within +/-2%... that isn't bad.

only musicians or true audiophiles are likely to notice it within that range.
 
Pulled off the platter and gave it a good cleaning and its running at 33.33 so that did the trick.

My parents were going to throw their collection out (75 LPs) and I couldn't let that happen so I ended up buying an extra suitcase to fly them home during my trip this summer. Imagine these ending up in a landfill

View attachment 10316


View attachment 10317
my sis grabbed all of the original beatles mono presses from our folks' collection. that was too bad because i care about this stuff and she doesn't. i've spent the past ten years grabbing those whenever i can find them (if you want good perspective on how special - and complex - the sound production was, try listening to sgt pepper on a mediocre or cheap turntable. the high end disappears.)

the scraps i got weren't bad. most of the stones material from 67-72, everything springsteen did through born in the USA, innvervisions & songs in the key of life. and an original press of dark side (with the poster and stickers that came with it).

can't complain.
 
This will probably work. If not. Tape.

Still running a little fast. Its a idler wheel system so I pulled off the cover, packed the TT bearing with new grease, cleaned and replaced any compenents with mineral oil and buffed the idler wheel with 1000 grit sandpaper.

I did read about adding teflon tape to the motor shaft to help slow down the rotation but not 100% sure if that will work.

Any experience with this type of system

20211025_145242.jpg
 
Last edited:
It's similar to the one I had ages ago.

Apply the tape (plumbers tape is fine) and test. It will take a few tries to get it just right.

The beauty is you can easily remove it if it doesn't work.
 
Back
Top